Hyundai Excel

Defect: IN SOME VEHICLES, THE MANUFACTURER'S PROTECTIVE INTERNAL COATING OF THE ELECTRONIC CRANK ANGLE SENSOR DOES NOT MEET SPECIFICATIONS, WHICH CAN CAUSE AN OPEN CIRCUIT AT HIGH OPERATING TEMPERATURES. THIS CAN CAUSE THE VEHICLE TO STALL.

Risc: ENGINE STALLING HAS THE POTENTIAL TO RESULT IN A VEHICLE CRASH IF IT OCCURS WHILE THE VEHICLE IS MOVING.

Remediul producătorului: DEALERS WILL INSPECT THE CRANK ANGLE SENSOR TO DETERMINE WHETHER THE SENSOR IS INVOLVED IN THE RECALL, AND REPLACE ANY SENSOR FOUND WITH THE DEFECTIVE INTERNAL COATING.

Defect: THE VEHICLES FAILED THE LATERAL MOVING BARRIER IMPACT TEST REQUIREMENTS OF FMVSS 301, "FUEL SYSTEM INTEGRITY." THE FUEL LEAKAGE FROM THE GAS TANK EXCEEDED THE MAXIMUM ALLOWABLE AMOUNT OF SPILLAGE.

Risc: IN THE EVENT OF AN ACCIDENT, THE FUEL SPILLAGE CAN RESULTIN A FIRE IF EXPOSED TO A SOURCE OF IGNITION.

Remediul producătorului: HYUNDAI HAS DEVELOPED AN APPROPRIATE COUNTERMEASURE THAT WILL COMPLY WITH ALL REQUIREMENTS OF FMVSS 301.

Defect: THE HEATER CONTROL VALVE STEM DOES NOT MEET THE MATERIAL SPECIFICATIONS. HIGH COOLANT TEMPERATURES CAN CAUSE THE STEM TO LEAK.

Risc: THIS CAN RESULT IN A BURN INJURY TO THE FRONT SEAT PASSENGER'S FEET AND LEGS.

Remediul producătorului: DEALERS WILL INSPECT AND REPLACE DEFECTIVE VALVE STEMS.

Defect: IF CRUISE CONTROL MAIN SWITCH IS IN THE ON POSITION WHEN ENGINE IS STARTED, SYSTEM CAN BE AFFECTED BY A SHORT DURATION VOLTAGE DROP CAUSED BY OPTIONAL HI-POWER (H340) RADIO.

Risc: THIS COULD CAUSE ERRATIC CRUISE CONTROL OPERATION, WHICHCOULD RESULT IN AN ACCIDENT.

Remediul producătorului: REPLACE ELECTRONIC CONTROL MODULE.

Defect: THE MANUAL TRANSMISSIONS MAY LOCK UP FROM INSUFFICIENT LUBRICATION OF THE GEARS IN THE TRANSMISSION CASE. THIS CAN CAUSE THE DRIVE WHEELS TO SEIZE AND THE VEHICLE TO COME TO A SUDDEN STOP.

Risc: SUDDEN STOPS WITHOUT PRIOR WARNING CAN CAUSE VEHICLEOCCUPANTS TO BE THROWN AROUND IN THE CAR, AND CAUSE LOSS OF VEHICLE CONTROLWHICH COULD RESULT IN AN ACCIDENT.

Remediul producătorului: HYUNDAI WILL PERFORM A COST FREE TRANSMISSION OIL CHANGE.

Defect: DETERIORATION OF THE REED VALVE SUBASSEMBLY MAY LEAD TO A MALFUNCTION WITHIN THE SECONDARY AIR SUPPLY PORTION OF THE EMISSION CONTROL SYSTEM. THE SCREWS WHICH ATTACH THE REEDS TO THE REED VALVE SUBASSEMBLY MAY RUST, AND IF THE RUSTING BECOMES SEVERE, THE SCREW HEADS WILL ERODE AND ALLOW THE REEDS TO SEPARATE FROM THE REED VALVE SUBASSEMBLY. CORROSION MAY ALSO OCCUR ON THE REED VALVE SUBASSEMBLY, DEFORMING THE REED SEATS AND PREVENTING THE REEDS FROM CLOSING PROPERLY. SEPARATION OF THE REEDS FROM THE REED VALVE SUBASSEMBLY OR IMPROPER CLOSING OF THE REEDS ALLOW HOT EXHAUST GASES TO FLOW BACKWARD INTO THE PLASTIC SECONDARY AIR FILTER CASE WHEN THE VEHICLE IS BEING DRIVEN. THESE HOT EXHAUST GASES MAY MELT THE SECONDARY PLASTIC AIR FILTER CASE.

Risc: THE MELTING PLASTIC AIR FILTER CASE MAY LEAD TO A FIREIN THE ENGINE COMPARTMENT.

Remediul producătorului: REPLACE THE REED VALVE SUBASSEMBLY WITH ONE WHOSE METAL COMPONENTS ARE FABRICATED FROM CORROSION RESISTANT STAINLESS STEEL.

Defect: A COTTER PIN IN THE BRAKE PEDAL TO BRAKE MASTER CYLINDER LINKAGE ASSEMBLY MAY BE MISSING. THIS PIN ACTS AS A RETAINER FOR THE BRAKE MASTER CYLINDER PUSHROD CLEVIS PIN. CONSEQUENCE OF DEFECT: THE CLEVIS PIN MAY SLIDE OUT CAUSING THE MASTER CYLINDER/BRAKE PEDAL LINKAGE TO BECOME DISENGAGED. IF THIS LINKAGE BECOMES DISENGAGED THE SERVICE BRAKES CANNOT BE APPLIED, CREATING THE RISK OF A CRASH WITHOUT PRIOR WARNING.

Remediul producătorului: INSPECT AND INSTALL BRAKE LINKAGE COTTER PIN AS NECESSARY.