Nissan Maxima

Defect: Nissan North America, Inc. (Nissan) is recalling certain model year 2016-2017 Nissan Maxima vehicles manufactured February 10, 2015, to August 19, 2016 and equipped with Intelligent Cruise Control, 2015-2017 Murano vehicles manufactured August 22, 2014, to August 19, 2016 and equipped with Intelligent Cruise Control, and 2015-2016 Murano Hybrid vehicles manufactured August 22, 2014, to July 19, 2016. The affected vehicles have Anti-Lock Brake (ABS) actuator pumps that may allow brake fluid to leak onto an internal electrical circuit board.

Risk: A brake fluid leak onto the circuit board may result in an electrical short, increasing the risk of a fire.

Manufacturer fix: Nissan will notify owners, and dealers will inspect the ABS Actuator, replacing it as necessary, free of charge. The recall began on December 12, 2016. Owners may contact Nissan customer service at 1-800-647-7261. Note: When brake fluid has leaked onto the circuit board, the ABS warning lamp will remain illuminated for more than 10 seconds after engine start up. If this occurs, owners are advised to park the vehicle outdoors away from other vehicles or structures and to not drive the vehicle.

Defect: Nissan North America, Inc. (Nissan) is recalling certain model year 2016 Murano vehicles manufactured December 17, 2015, to February 11, 2016, and 2016 Maxima vehicles manufactured November 25, 2015, to February 12, 2016 and equipped with an antilock braking system (ABS) and Vehicle Dynamic Control (VDC). The ABS actuator may have a damaged O-ring that may result in a lack of brake fluid pressure.

Risk: Insufficient brake fluid pressure may lengthen the distance needed to stop the vehicle, increasing the risk of a crash.

Manufacturer fix: Nissan will notify owners, and dealers will inspect and replace the ABS actuator, as necessary, free of charge. The recall began on May 16, 2016. Owners may contact Nissan customer service at 1-800-647-7261.

Defect: CERTAIN PASSENGER VEHICLES EQUIPPED WITH AN 'INTELLIGENT KEY' FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 114, "THEFT PROTECTION." DURING AN INSPECTION OF SOME VEHICLES AT THE ASSEMBLY PLANT, IT WAS FOUND THAT THE STEERING WHEEL WAS LOCKED WITH THE IGNITION KNOB IN THE "OFF" POSITION BUT THE VEHICLE TRANSMISSION NOT BEING IN THE "PARK" POSITION.

Risk: IF THE KEY IS TURNED TO THE "OFF" POSITION WITHOUT THE TRANSMISSION BEING IN THE "PARK" POSITION, IT IS POSSIBLE THAT THE STEERING WHEEL CAN LOCK WHEN TURNED TO THE RIGHT.

Manufacturer fix: DEALERS WILL INSPECT AND REPLACE THE STEERING WHEEL LOCK ASSEMBLY FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 18, 2006. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.

Defect: CERTAIN VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 225, "CHILD RESTRAINT ANCHORAGE SYSTEMS." THE LOWER ANCHORAGE BRACKETS IN THE REAR SEATS DO NOT MEET THE LOCATION REQUIREMENT IN THIS STANDARD. THIS MAY CAUSE DIFFICULTY IN ATTACHING SOME CHILD SEATS TO THESE BRACKETS.

Risk: IF A CHILD SEAT IS NOT PROPERLY SECURED, THERE IS AN INCREASED RISK OF INJURY TO THE SEAT OCCUPANT IN THE EVENT OF A CRASH.

Manufacturer fix: DEALERS WILL REPLACE THE LOWER ANCHORAGE BRACKETS WITH MODIFIED BRACKETS TO ENSURE THAT THE STANDARD IS MET. THE RECALL BEGAN ON AUGUST 28, 2006. THE INFINITI Q45 MODEL VEHICLES ARE BEING CAMPAIGNED UNDER A SEPARATE RECALL (PLEASE SEE 05V374000). OWNERS SHOULD CONTACT NISSAN AT 1-800-647-7261 OR INFINITI AT 1-800-662-6200.

Defect: ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH THE DRIVER PREFERRED PACKAGE, THE WIRE HARNESS FROM THE DRIVER'S SEAT POWER LUMBAR SUPPORT SWITCH MAY BE ROUTED INCORRECTLY AND COULD BE PINCHED UNDER THE DRIVER SEAT.

Risk: A PINCHED HARNESS, IN COMBINATION WITH DRIVING VIBRATION, MAY RESULT IN A SHORT CIRCUIT IN THE HARNESS THAT COULD LEAD TO A FIRE IN THE SEAT.

Manufacturer fix: DEALERS WILL REPLACE THE WIRE HARNESS AND ROUTE IT CORRECTLY. THE RECALL BEGAN ON JANUARY 16, 2006. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.

Defect: ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH SKYVIEW ROOFS, THE GLASS FOR THE ROOF MAY NOT HAVE BEEN QUENCHED PROPERLY AFTER THE FORMING PROCESS, RESULTING IN TEMPER IMBALANCE.

Risk: THIS COULD CREATE EXCESSIVE INTERNAL STRESS IN THE GLASS AND EVENTUALLY CAUSE THE GLASS TO SHATTER, CREATING A RISK OF INJURY.

Manufacturer fix: DEALERS WILL INSPECT AND REPLACE THE GLASS IN THE SKYVIEW ROOF. THE RECALL BEGAN ON SEPTEMBER 7, 2004. OWNERS SHOULD CONTACT NISSAN AT 1-800-647-7261.

Defect: ON CERTAIN PASSENGER VEHICLES, THE PIN AT THE END OF THE FRONT SUSPENSION TRANSVERSE LINK (LOWER CONTROL ARM) COULD BREAK WHERE IT IS MOUNTED TO THE FRAME.

Risk: THIS CAN CAUSE A KNOCKING SOUND AND ABNORMAL STEERING. THIS COULD RESULT IN DIFFICULTY CONTROLLING THE VEHICLE AND INCREASING THE RISK OF A CRASH.

Manufacturer fix: DEALERS WILL REPLACE THE TRANSVERSE LINKS ON THE LEFT AND RIGHT SIDES WITH NEW ONES. OWNER NOTIFICATION BEGAN JULY 29, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT NISSAN AT 1-800-647-7261 OR INFINITI AT 1-800-662-6200.

Defect: ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH A TRACTION CONTROL SYSTEM, THE ODOMETER IN THE SUBJECT VEHICLES REGISTERS DISTANCE IN KILOMETERS INSTEAD OF MILES AS IS SPECIFIED IN THE DESIGN. THE ODOMETER DOES NOT HAVE A LABEL THAT INDICATES "KILOMETERS" OR "KM" AS REQUIRED BY FMVSS NO. 101, "CONTROLS AND DISPLAYS."

Manufacturer fix: DEALERS WILL INSPECT THE ODOMETER TO DETERMINE IF IT IS CORRECT AND, IF NOT, WILL REPLACE THE SPEEDOMETER/ODOMETER ASSEMBLY. OWNER NOTIFICATION BEGAN DECEMBER 12, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT NISSAN AT 1-800-647-7261.

Defect: IN SOME UNDERBODY IMPACTS THE AIRBAG SENSOR ACTIVATES AND SENDS A SIGNAL TO THE AIRBAG, LOCATED IN THE CENTER OF THE STEERING WHEEL, CAUSING THE DRIVER'S SIDE AIRBAG TO INFLATE.

Risk: AIRBAG INFLATION MAY OCCUR WHEN IT IS NOT NEEDED TO PROTECT THE DRIVER AND MAY RESULT IN MINOR INJURIES TO THE DRIVER FROM THE INFLATING AIRBAG.

Manufacturer fix: A TUNNEL SENSOR OF DIFFERENT DESIGN WILL BE INSTALLED ON THE AFFECTED VEHICLES.

Defect: THE ALUMINUM WHEELS WERE CLEAR COATED SEVERAL TIMES TO PROTECT THE METAL FINISH. SOME EXCESSIVE COATING CAN LEAVE THE WHEEL NUTS AN EXCESSIVE DISTANCE FROM THE WHEEL HUB WHEN TIGHTENED, ALLOWING THEM TO LOOSEN OVER TIME.

Risk: THIS CAN CAUSE THE HUB BOLTS TO BREAK AND RESULT IN THE WHEEL SEPARATING FROM THE VEHICLE AND A POSSIBLE ACCIDENT.

Manufacturer fix: DEALERS WILL REMOVE THE CLEAR PLASTIC COATING FROM THE BRAKE ROTOR MATING SURFACE ON THE BACK OF EACH WHEEL AND FROM THE WHEEL NUT MATING SURFACES. THE WHEELS WILL BE REINSTALLED AND THE WHEEL NUTS TIGHTENED. WHEELS, HUB BOLTS, AND NUTS WILL BE REPLACED IF NECESSARY.

Defect: IT IS POSSIBLE FOR A MIXTURE OF MUD AND SALT TO GET TRAPPED BETWEEN THE FUEL FILLER TUBE AND WHEEL HOUSING. THE TRAPPED MUD AND SALT CAN RESULT IN CORROSION OF THE FUEL FILLER TUBE AND THE WHEEL HOUSING.

Risk: SIGNIFICANT CORROSION OF THE FUEL FILLER TUBE MAY RESULT IN FUEL LEAKS WHICH IN THE PRESENCE OF AN IGNITION SOURCE COULD RESULT IN A FIRE. IN ADDITION, THE LEFT REAR SEAT BELT RETRACTOR IS MOUNTED TO THE WHEEL HOUSING AND IN THE EVENT OF SIGNIFICANT CORROSION, AND THE MOUNTING COULD FAIL IN A VEHICLE CRASH.

Manufacturer fix: DEALERS WILL INSPECT THESE VEHICLES AND CORRECTIVE ACTION WILL BE TAKEN DEPENDING UPON THE EXTENT OF THE CORROSION.

Defect: THERE MAY BE INSUFFICIENT THICKNESS OF ADHESIVE IN THE CONTACT AREA BETWEEN THE BOTTOM OF THE FRONT WINDSHIELD GLASS AND THE BODY. CONSEQUENCE OF DEFECT: THIS LACK OF ADHESIVE MAY CAUSE THE WINDSHIELD TO DISMOUNT IN AN ACCIDENT, THUS FAILING TO COMPLY WITH FMVSS 212, WINDSHIELD MOUNTING AND WHICH MAY ALLOW THE OCCUPANTS TO BE EJECTED OUT OF THE CAR, CAUSING MORE SERIOUS INJURIES OR DEATH.

Manufacturer fix: ADD MORE ADHESIVE TO BOTTOM OF FRONT WINDSHIELD GLASS.