Ford Econoline

Defect: Ford Motor Company (Ford) is recalling certain 2026 Econoline vehicles. The heating, ventilation and air-conditioning (HVAC) system blower motor may fail, which can cause the defrosting and defogging system to become inoperative.

Risk: An inoperative windshield defrosting and defogging system may decrease the driver's visibility, increasing the risk of a crash.

Manufacturer fix: Dealers will replace the HVAC blower motor assembly, free of charge. Owner notification letters were mailed January 30, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SB4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov beginning October 28, 2025.

Defect: Ford Motor Company (Ford) is recalling certain 2009-2016 Ford Econoline vehicles equipped with a 5R110W transmission, 5.4L engine, and a school bus or ambulance preparation package. A weld within the coast clutch may fail, causing an unexpected loss of drive power.

Risk: A sudden loss of drive power increases the risk of a crash. Transferring occupants of a disabled school bus or ambulance to another vehicle increases their risk of injury.

Manufacturer fix: Ford will notify owners, and dealers will replace the single-engaging coast one-way clutch with a new dual-engaging one-way clutch, free of charge. The recall began August 19, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S20.

Defect: SUNSET VANS IS RECALLING 169 MY 2005-2007 ECONOLINE, G SERIES AND SPRINTER TRUCKS BUILT ON DODGE, FORD AND CHEVROLET CHASSIS AND EQUIPPED WITH RICON PLATFORM STYLE WHEELCHAIR LIFTS. THESE LIFTS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 403, "PLATFORM LIFT SYSTEM ACCESSIBLE FOR MOTOR VEHICLES." THE ANTI-STOW INTERLOCK MAY NOT DETECT THE PRESENCE OF A WHEELCHAIR OR MOBILITY AID USER. THE PRESSURE SENSING SWITCH THAT DETECTS THE PRESENCE OF WEIGHT ON THE PLATFORM WAS NOT ADJUSTED TO THE NECESSARY SENSITIVITY LEVEL. THE LIFT COULD STOW EVEN THOUGH SOMEONE OR SOMETHING IS STILL ON THE LIFT.

Risk: A LIFT OCCUPANT CAN BE INJURED SHOULD THE LIFT BEGIN TO STOW UNINTENTIONALLY.

Manufacturer fix: SUNSET VANS IS WORKING WITH RICON TO CORRECT THE WHEELCHAIR LIFTS FREE OF CHARGE (PLEASE SEE 07E097). OWNERS MAY CONTACT RICON AT 1-818-267-3000 OR SUNSET VANS AT 1-888-280-8267.

Defect: SUNSET VANS IS RECALLING 267 MY 2005-2007 ECONOLINE, G SERIES AND SPRINTER TRUCKS BUILT ON DODGE, FORD AND CHEVROLET CHASSIS AND EQUIPPED WITH RICON PLATFORM STYLE WHEELCHAIR LIFTS. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 404, "PLATFORM LIFT INSTALLATIONS IN MOTOR VEHICLES." THE THRESHOLD WARNING SYSTEM MAY NOT DETECT THE PRESENCE OF A WHEELCHAIR OR MOBILITY AID USER IN A CERTAIN SPOT WITHIN THE DEFINED THRESHOLD AREA.

Risk: THE USER OF THE LIFT COULD BE INJURED SHOULD THE LIFT MOVE UNINTENTIONALLY.

Manufacturer fix: SUNSET VANS IS WORKING WITH RICON TO CORRECT THE WHEELCHAIR LIFTS FREE OF CHARGE (PLEASE SEE 07E095). OWNERS MAY CONTACT RICON AT 1-818-267-3000 OR SUNSET VANS AT 1-888-280-8267.

Defect: ON CERTAIN CUTAWAY CHASSIS CAB WITH THE SCHOOL BUS OPTION, TWO BRACKETS AND TWO OUTRIGGER MEMBERS ARE MISSING IN THE AREA OF THE FUEL TANK.

Risk: THE BRACKETS AND OUTRIGGER MEMBERS ARE INTENDED TO ENHANCE CRASH PERFORMANCE.

Manufacturer fix: FORD WILL SEND TECHNICIANS TO THE OWNER'S LOCATION TO INSPECT AND ADD THE BRACKETS AND OUTRIGGERS AS REQUIRED. OWNER NOTIFICATION BEGAN ON SEPTEMBER 3, 2003. OWNERS SHOULD CONTACT FORD AT 1-800-392-3673.

Defect: VEHICLE DESCRIPTION: CERTAIN CREW VANS FAILED TO COMPLY WITH THE REQUIREMENTS OF FMVSS 225, "CHILD RESTRAINT ANCHORAGE SYSTEMS." THESE VEHICLES, WHICH ARE DESIGNATED AS TRUCKS, ARE 5 PASSENGER VEHICLES WITH THREE DESIGNATED SEATING POSITIONS IN THE SECOND ROW SEATS. THEY WERE BUILT WITHOUT CHILD SEAT TETHER ANCHORAGE BRACKETS IN THE CENTER POSITION OF THE SECOND ROW SEAT. ALSO THE OWNER GUIDES DO NOT ADDRESS THE CHILD SEAT TETHER ANCHORAGES IN THE CENTER SECOND ROW SEAT POSITION.

Risk: IN THE EVENT OF A CRASH, THE CHILD SEAT MAY NOT BE PROPERLY ATTACHED INCREASING THE RISK OF INJURY TO THE CHILD.

Manufacturer fix: DEALERS WILL INSTALL THE CHILD SEAT TETHER ANCHORAGES AT THE CENTER SECOND ROW SEATING POSITION, AND ALSO REPLACE THE VEHICLE OWNER GUIDES WITH NEW VERSIONS PROVIDING THE REQUIRED WRITTEN INSTRUCTIONS. ELEVEN VEHICLES ARE AT DEALERSHIPS AND ASSEMBLY PLANT PERSONNEL WILL REPAIR THESE UNITS AT THE AFFECTED DEALERSHIPS. ARRANGEMENTS HAVE BEEN MADE FOR THE RETURN OF THE ONE UNIT THAT HAD BEEN SOLD. NO OTHER OWNER NOTIFICATION WILL BE REQUIRED.

Defect: VEHICLE DESCRIPTION: PICKUP TRUCKS BUILT WITH SINGLE REAR WHEELS AND EQUIPPED WITH 3.55:1 AND 3.73:1 AXLE RATIO. THESE VEHICLES WERE BUILT WITH INCORRECT SPEEDOMETER DRIVEN GEARS, RESULTING IN A LOWER SPEEDOMETER READING THAN THE ACTUAL VEHICLE SPEED BEING DRIVEN.

Risk: THIS CAN RESULT IN THE VEHICLE BEING DRIVEN AT AN UNSAFE OR ILLEGAL SPEED SHOULD THE DRIVER NOT REALIZE THAT HIS VEHICLE ROAD SPEED IS GREATER THAN THE SPEEDOMETER INDICATION.

Manufacturer fix: DEALERS WILL INSTALL THE CORRECT SPEEDOMETER GEAR.

Defect: VEHICLE DESCRIPTION: CUTAWAYS AND STRIPPED CHASSIS WITH SINGLE REAR WHEELS. THE LUG NUTS CAN POTENTIALLY BOTTOM OUT ON A SHOULDER ON THE STUDS.

Risk: IF THIS OCCURS, THERE CAN BE AN INADEQUATE CLAMP LOAD TO ATTACH THE WHEEL TO THE AXLE, RESULTING IN NOISE, DAMAGE TO THE WHEEL AND HUB, OR IN EXTREME CASES, LOSS OF A REAR WHEEL WHILE THE VEHICLE IS BEING DRIVEN.

Manufacturer fix: DEALERS WILL REPLACE THE REAR WHEEL ATTACHING STUDS.

Defect: THE BATTERY CABLE HARNESS DOES NOT HAVE ADEQUATE PROTECTION FROM CONTACTING AND BEING DAMAGED BY THE RIGHT ENGINE MOUNT.

Risk: IF THE BATTERY CABLE OR STARTER WIRE INSULATION IS DAMAGED BY SUCH CONTACT, A SHORT TO GROUND CAN OCCUR RESULTING IN OVERHEATING OF THE WIRING AND POSSIBLE IGNITION OF SURROUNDING COMPONENTS.

Manufacturer fix: DEALERS WILL INSPECT FOR CHAFING OF THE CABLE AND WILL ADD INSULATION AND A TIE STRAP TO THE BATTERY CABLE HARNESS.

Defect: VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER VANS AND STRIPPED CHASSIS. THERE IS INTERFERENCE BETWEEN THE PARKING BRAKE CABLE AND THE FUEL LINE WHICH, OVER TIME, CAN RESULT IN DAMAGE TO THE FUEL LINE CAUSING FUEL LEAKAGE.

Risk: IF THERE IS FUEL LEAKAGE IN THE PRESENCE OF AN IGNITION SOURCE, FIRE COULD RESULT.

Manufacturer fix: DEALERS WILL REPLACE THE FUEL SUPPLY LINE. IN ADDITION, A PIECE OF ANTI-ABRASION INSULATION WILL BE INSTALLED TO PREVENT ABRASION OF THE FUEL LINE.

Defect: THE PARKING BRAKE FRONT CABLES WERE BUILT LONGER THAN APPROPRIATE THAT REDUCES THE PERFORMANCE OF THE PARKING BRAKE IN CERTAIN CIRCUMSTANCES, AND FAILS TO FULLY COMPLY WITH ALL THE REQUIREMENTS OF FMVSS NO. 105, "HYDRAULIC BRAKE SYSTEMS."

Risk: CONSEQUENCE OF NON-COMPLIANCE: THE EFFECTIVENESS OF THE PARKING BRAKE SYSTEM ON A SEVERE GRADE MAY BE DIMINISHED.

Manufacturer fix: DEALERS WILL REPAIR THE PARKING BRAKE SYSTEM ON THE AFFECTED VEHICLES.

Defect: THE FUEL FILLER HOSE OR FUEL FILLER VENT HOSE WAS DAMAGED BY A DRILL BIT USED TO INSTALL THE DSO PACKAGE ATTACHING HARDWARE ONTO THE FLOOR PAN.

Risk: IF EITHER OF THE HOSES WAS PENETRATED BY THE DRILL BIT,FUEL LEAKAGE COULD RESULT, PARTICULARLY DURING FUELING OF THE VEHICLE. IN THEPRESENCE OF AN IGNITION SOURCE, THIS COULD RESULT IN FIRE.

Manufacturer fix: REPLACE THE FUEL FILLER AND VENT HOSES AND RELOCATE THE MOUNTING HARDWARE IN THE FLOOR PAN.

Defect: THE TIRE CERTIFICATION LABELS INCORRECTLY IDENTIFY THE VEHICLE TIRE REQUIREMENTS AS P235/75R15 SL (STANDARD LOAD), RATHER THAN AS P235/75R15 XL (EXTRA LOAD).

Risk: THE CERTIFICATION LABELS ON THE AFFECTED VEHICLES DO NOTCOMPLY WITH FMVSS 120, "TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THANPASSENGER CARS." INCORRECT TIRE SELECTION COULD RESULT IN SUDDEN FAILURE OFA TIRE WHILE THE VEHICLE IS IN MOTION, AND RESULT IN A VEHICLE ACCIDENT.

Manufacturer fix: CORRECT TIRE INFORMATION LABELS AND INSTALLATION INSTRUCTIONS WILL BE MAILED TO THE OWNERS OF THESE VEHICLES. OWNERS WILL BE INSTRUCTED THAT DEALERS CAN INSTALL THE LABEL PROVIDED IF THEY PREFER.

Defect: THE REAR SHOCK CROSSMEMBER OF THE FRAME CAN CRACK AND SEPARATE FROM THE FRAME.

Risk: SEPARATION OF THE REAR SHOCK CROSSMEMBER FROM THE FRAMECAN RESULT IN LOSS OF VEHICLE CONTROL AND AN ACCIDENT.

Manufacturer fix: REPLACE THE REAR CHOCK CROSSMEMBER WITH A SHOCK CROSSMEMBER MADE OF HIGH STRENGTH STEEL.

Defect: UNDER CERTAIN CONDITIONS, THE SNAP RING THAT LOCATES THE PARK GEAR ON THE OUTPUT SHAFT OF THE TRANSMISSION MAY FRACTURE.

Risk: WHEN THE GEAR IS PLACED IN PARK, THE PARK GEAR WOULD NOTENGAGE, ALLOWING THE TRUCK TO ROLL FREELY IF THE PARKING BRAKE IS NOT PROPERLYSET. THIS COULD RESULT IN AN ACCIDENT.

Manufacturer fix: INSTALL IMPROVED SNAP RING AND REVISED TRANSMISSION EXTENSION HOUSING.

Defect: THE RUBBER THAT ENCASES BALL STUD AND SOCKET JOINT (CONNECTS STEERING DRAG LINK AND PITMAN ARM) MAY DETERIORATE, CAUSING METAL TO METAL CONTACT, AND MAY EVENTUALLY RESULT IN COMPLETE SEPARATION. CONSEQUENCE OF DEFECT: COMPLETE SEPARATION OF THE DRAG LINK TO PITMAN ARM CONNECTION RESULTS IN LOSS OF STEERING CONTROL WHICH MAY LEAD TO AN ACCIDENT.

Manufacturer fix: INSTALL NEW DRAG LINK ASSEMBLIES WITH STEEL BALL AND SOCKET JOINTS AT THE PITMAN ARM CONNECTIONS.

Defect: WHEN FRONTALLY IMPACTED INTO A FIXED BARRIER AT 30 MPH, AS SPECIFIED IN FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 301, THE LEFT FRAME RAILS OF SUCH VEHICLES MAY DISPLACE INBOARD, PINCHING THE FUEL/WATER SEPARATOR CANISTER BETWEEN THE FRAME RAIL AND ENGINE SUFFICIENTLY TO DISPLACE THE FUEL/WATER SEPARATOR DRAIN ROD, ALLOWING THE CONTENTS OF THE CANISTER TO DRAIN. CONSEQUENCE OF DEFECT: FUEL LEAK DURING OR AFTER A CRASH INCREASES THE POSSIBILITY OF A FIRE.

Manufacturer fix: INSTALL A CANISTER SHIELD, A REVISED DESIGN DRAIN ROD SHIELD, AND MODIFY FUEL/WATER SEPARATOR MOUNTING BRACKET.

Defect: EXPULSION OF FUEL DUE TO OVERPRESSURIZATION.

Risk: FUEL OR FUEL VAPORS IN THE PRESENCE OF AN IGNITIONSOURCE CAN CAUSE A FIRE.

Manufacturer fix: MODIFICATION OF THE BASE FUEL VENTING AND EMISSION CONTROL SYSTEM TO REDUCE OPERATING TEMPERATURES AND FUEL SYSTEM PRESSURES.

Defect: THE INVOLVED VEHICLES MAY NOT MEET THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, "FUEL SYSTEM INTEGRITY". IN A MOVING BARRIER IMPACT TEST FROM THE REAR AT 30 MPH, THE FASTENER ATTACHING THE FUEL SENDER GROUND WIRE TO THE FRAME CROSSMEMBER, AFT OF THE FUEL TANK, PIERCED THE FUEL TANK.

Manufacturer fix: THE FUEL SENDER GROUND WIRE ATTACHMENT ON ALL AFFECTED VEHICLES WILL BE RELOCATED TO ELIMINATE THE DANGER, WITHOUT CHARGE TO OWNER.

Defect: THE GEAR POSITION INDICATORS ON CERTAIN VEHICLES MAY BE TOO SHORT TO BE READILY VISIBLE TO SOME DRIVERS. THIS IS NOT IN COMPLIANCE WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 101, "CONTROLS AND DISPLAY", WHICH STATES THAT THE GEAR POSITION DISPLAY MUST BE VISIBLE TO DRIVER.

Manufacturer fix: IF POINTER OF GEAR POSITION INDICATOR IS FOUND TO BE TOO SHORT, IT WILL BE REPLACED WITHOUT CHARGE TO OWNER.

Defect: THE INSTRUMENT PANELS ON THE INVOLVED VEHICLES CAN BE BROKEN DURING OCCUPANT IMPACT.

Manufacturer fix: THE DEALER WILL INSTALL A FIELD-INSTALLABLE PANEL PAD, FREE OF CHARGE, ON ALL AFFECTED VEHICLES.

Defect: CERTAIN VEHICLES MAY NOT CONTAIN THE SPECIFIED BODY MOUNTED HEAT SHIELDS. THIS COULD CAUSE HIGH FLOOR PAN TEMPERATURES WHEN THE ENGINE IS IDLED FOR EXTENDED PERIODS OF TIME. FOULED SPARK PLUGS OR OTHER ENGINE CONDITIONS COULD FURTHER INCREASE EXHAUST TEMPERATURES.

Manufacturer fix: THE DEALER WILL INSTALL THE NECESSARY FRAME MOUNTED HEAT SHIELD, IF MISSING.